Highside Chemicals
Supco
   
 
 
     
Highside Chemical
11114 Reichhold Road - Gulfport, Mississippi 39503, USA

800-359-5599
228-896-9220
Fax: 228-896-9544

Email

 

HVAC Super Pro Kit HVAC Super Pro -
1.85 oz. Individually Packaged in Display Box
- Solderless One Part Copper Bonding
- Starts to set up in 20 seconds and forms a solid bond in 3 minutes
- In 12 minutes the bond will withstand 850psi of refrigerant pressure
- Bonding time in 1 minute for aluminum and is set in 4 minutes
- Approx. 2 Hours is fully cured and will withstand 1200psiof refrigerant pressure
- Compatible with all refrigerants and oils
- Use with standard copper or brass fittings
- Temperature range after cure: -65°F to 350°F (-54°C to 176°C)
- Bonds Copper, Aluminum and Brass in any Combination
- Single Part Formula - Easy to Use and No Mixing Required
- Bottle lasts Minimum of 12 Months After Opening
- Uses Standard ASE Fittings - No Expensive Tools or Special Fittings Required
- One Bottle Makes 200 or More Bonds on 1/2 -inch Tubing
- Makes the Same Number of Bonds as 1-1/2 Pounds of Braze at Approximately 25% of the Cost of 15% Silver Braze
- For all repairs and new installations
- Rated to 1200psi and -65°F to 350°F
Instant HVACR Patch INSTANT - HVAC/R PATCH -
Two part - Bonding Fluid and Micro Cells
- Point of Purchase - Bubble Pac Package
- For permanently sealing holes in all metals and rigid plastics
- Forms a high strength bond in seconds
- Full cure in 20 minutes - put equipment back in service
- Shore D 85+ hardness
- Rated at 350psi contained air or refrigeration pressure
- Handles 200°F (93.3°C) continuous temperature
Instant Plumbing Patch INSTANT - PLUMBING PATCH -
Two part - Bonding Fluid and Micro Cells
- Point of Purchase - Bubble Pac Package
- For permanently sealing holes in all metals and rigid plastics
- Forms a high strength bond in seconds
- Full cure in 20 minutes - put equipment back in service
- Shore D 85+ hardness
- Rated at 200psi contained pressure
- Handles 200°F (93.3°C) continuous temperature
Instant Automotive Patch INSTANT - AUTOMOTIVE PATCH -
Two part - Bonding Fluid and Micro Cells
- Point of Purchase - Bubble Pac Package
- For permanently sealing holes and cracks in all metals and rigid plastics used in the automotive industry
- Forms a high strength bond in seconds
- Full cure in 20 minutes
- Shore D 85+ hardness
- Rated at 350 psi contained pressure
- Handles 200°F (93.3°C) continuous temperature
- Repairs - Blown radiator hoses, radiators, fuel lines, fuel tanks, air lines, AC lines, RV holding tanks, and more
- Can be used on trim, lenses, cracked batteries and much more
Super Patch SUPER PATCH KIT
- For permanently repairing holes in copper and aluminum tubing
- Kit contains:
• A Stainless Steel Patch Rite Patch
• A Tube of Patch Rite Gel
• A Stainless Steel Hose Clamp
• 60 Grit Sandpaper
• Instructions
- Standard Sizes available: (O.D.) 3/8”, 5/8”, 7/8”, 1-1/8”
- Strength of bond 1200psi
Just for copper Just For Copper -
.35 oz. on point of purchase card, Two Sizes - (10g and 50g),
- 5 Sec Set
- Is clear in color
- Holds 200psi 7-minutes after bonding
- Holds 500psi 4-hours after bonding
- Tensile strength (strength to pull pipe from fitting) in excess of 1000psi
- Rotating strength (Strength to twist pipe from fitting) 350psi
- Temperature range from -40°C to 110°C (-40°F to 230°F)
- Use on all rigid copper pipe up to 2.5 inches @500psi, or any size copper pipe used as a drain or in low pressure applications
- Fills gaps up to .0025
- Non-toxic, non-flammable, non-conductive and non-irritant
Just For Copper Pro Just For Copper PRO -
1.76 oz. (50g) on point of purchase card. Also available in Display Box.
- ANSI 61 Certified
- 10 Sec Set
- is brown in color for inspectors benefit
- Sets in l0-seconds
- Holds 200psi 7-minutes after bonding
- Holds 500psi 4-hours after bonding
- Tensile strength (strength to pull pipe from fitting) in excess of 1300psi
- Rotating strength (Strength to twist pipe from fitting) 385psi
- Temperature range from -40°C to 118°C (-40°F to 245°F)
- Use on all rigid copper pipe up to 2.5 inches @500psi, or any size copper pipe used as a drain or in low pressure applications
- Fills gaps up to .0025
- Non-toxic, non-flammable, non-conductive and non-irritant
Just For Copper Epoxy Putty Just For Copper - Epoxy Putty -
Bonds Copper, Brass and Bronze
- 10 Minutes Working Time, starts to set in 15 minutes
- Mix by hand
- 90% cure in 4 Hours. Full cure, 24 Hours
- Temperature range (continuous): 260°C (500°F)
- Shelf Life: 2 Years
- Hardness: Shore D 85
- Compression Strength: 18,000psi, Tensile: 5,950psi, Shear: 710psi
Just For Copper Thread Sealant Just For Copper - Thread Sealant -
Two sizes. (15g and 50g) Tubes. On point of purchase card
- For Brass and Copper
- Holds 2000 psi
- Remains pliable at temperatures ranging from -54°C to 149C (-65°F to 300°F)
- Resistant to Fuels, lubricants, most solvents, base, and many acids
- Non-toxic, non-flammable and non-irritant
- Easy removal with normal wrench pressure

 

 

 

 

HOME
SDS - MSDS LINKS
HOW TO USE PRODUCT VIDEOS
 
 
CONTACT US

 


Also Introducing ...
Heat Shield Gel

Highside Chemical Heat Shield Gel

 

ALL TEMPERATURE
BARRIER SPRAY


Heat Shield Gel protects surrounding surfaces during all types of hot work including welding, brazing and soldering. Sprays on as a gel and adheres to the surfaces to be protected without dripping. Clear gel evaporates within 24-48 hours. Will not stain protected surfaces which eliminates clean ups.

Heat Shield Gel is designed to be used on wood, insulation, valves, piping and drywall. Safe formula will not harm skin and is non-toxic. Helps prevent flare ups and risk of fire to surrounding areas.

• Protects Heat Sensitive
Components
• No-Drip Formula
• Non-Corrosive
• Non-Toxic
• Non-Staining
• No Cleanup

• Prevents heat damage to nearby components during soldering, brazing or welding.
• The unique gelled formula sticks to the surface without drips and runs.
• Protects adjoining areas made of wood, wallboard, insulation, etc.

Available Now!